加速溶剂萃取-固相萃取-硅胶吸附色谱-电喷雾质谱法测定纺织品中的烷基酚聚氧乙烯醚

建立了测定纺织品中壬基酚聚氧乙烯醚和辛基酚聚氧乙烯醚的硅胶吸附色谱-电喷雾质谱分析方法.不同类型的纺织品样品采用加速溶剂萃取法,以无水乙醇为提取溶剂,在10.3 MPa和100 ℃下静态循环提取2次,提取液经Sep-Pak Carbon/NH2石墨化碳黑/氨基复合型固相萃取柱净化,以Waters Spherisorb S3W(150 mm×2.0 mm, 3 μm)色谱柱为分离柱,乙腈-水体系为流动相梯度洗脱,在电喷雾质谱正离子模式下进行定性及定量分析.壬基酚聚氧乙烯醚的方法检出限为10～40 μg/kg,在1～20 mg/kg的3个添加水平范围内的平均回收率为81.4%～95.9%,相对标准偏差均小于12.5%.辛基酚聚氧乙烯醚的方法检出限为10～30 μg/kg,在1～20 mg/kg的3个添加水平范围内的平均回收率为80.2%～96.8%, 相对标准偏差均小于13.0%.本方法准确、简便、快速,可用于纺织品的实际检验工作.     

Application of ultra-high-pressure liquid chromatography–tandem mass spectrometry to the determination of multi-class pesticides in environmental and wastewater samples: Study of matrix effects

An ultra-high-pressure liquid chromatography–tandem mass spectrometry (UHPLC–MS/MS) method for the determination of 37 pesticides (herbicides, insecticides and fungicides) in environmental and wastewater has been developed. To efficiently combine UHPLC with MS/MS, a fast-acquisition triple quadrupole mass analyzer was used. This analyzer (minimum dwell time, 5 ms) allows acquiring up to three simultaneous transitions in the selected reaction monitoring mode for each compound assuring a reliable identification without resolution or sensitivity losses. A pre-concentration step based on solid-phase extraction using Waters Oasis HLB cartridges (0.2 g) was applied with a 100-fold pre-concentration factor along the whole analytical procedure. The method was validated based on European SANCO guidelines using surface, ground, drinking and treated water (from an urban solid residues treatment plant) spiked at two concentration levels (0.025 and 0.1 μg/L), the lowest having been established as the limit of quantification objective. The method showed excellent sensitivity, with instrumental limits of detection ranging from 0.1 to 7 pg. It was applied to environmental water samples (ground and surface water) as well as to samples of urban solid waste leachates (raw leachate and treated leachate after applying reversed osmosis) collected from a municipal treatment plant. Matrix effects have been studied in the different types of water samples analyzed, and several isotope-labelled internal standards have been evaluated as a way to compensate the signal suppression observed for most of the compounds studied, especially in wastewater samples. As a general remark, only those pesticides which response was corrected using their own isotope-labelled molecule, could be satisfactorily corrected in all type of samples, assuring in this way the accurate quantification in all matrix samples.     

以催化裂化废催化剂为原料合成NaY分子筛的研究

针对催化裂化(FCC)废催化剂的回收利用问题,提出了一种废催化剂再利用的方法,即以FCC废催化剂为铝源,合成时只补充部分硅源,采用自制的高效NaY沸石导向剂,水热合成NaY分子筛。同时,以普通的化工原料合成了对比试样Y型分子筛。讨论了不同的FCC废催化剂预处理方式对合成产物性能的影响,发现以经过碱熔活化处理的废催化剂为原料合成的Y分子筛拥有更高的结晶度和纯度。采用X射线衍射、热分析、程序升温脱附法(NH3-TPD)和N₂静态容量吸附法对结晶产物和对比样品的晶体结构,热稳定性、酸性质、比表面积以及孔分布进行了表征。结果显示,以FCC废催化剂为原料完全可以合成出与普通原料性能接近的NaY分子筛。其BET比表面积可以达到615 m²·g^-1,孔体积可达0.38 cm³·g^-1,孔径集中在0.51 nm左右。     

The Research of Sulfuric Acidic Recycling of Aluminum Industry Fluorine-containing Waste Products

The article presents the method of recycling aluminum industry fluorine-containing waste products to produce hydrogen fluoride. We carried out the estimate of the thermodynamic parameters of sulfuric acidic recycling of fluorine-containing waste products. We considered the necessity of waste products preliminary oxidizing roast stage to reduce carbonic constituent due to the interaction between carbonic constituent blocks of the sulfuric acid and waste products. We also carried out the researches for kinetic characteristics and to determine the optimal conditions for the to recycle sulfuric acidic in the fluorine-containing waste products.     

Ash and Slag Waste as a Secondary Raw Material

In the process of industrial corporation activities a lot of waste, which pollutes the atmosphere, is generated, for example ash and slag. In Tomsk region, by estimates, ash stores occupy about 600 hectares, which contain about 25 million tons by weight. In Russian thermal power-stations ash disposal areas there are about 1.3 billion tons of ash, and only 10% of it is used. That is why this problem is topical enough. In this paper the scheme of producing ash ceramic bricks and complex ash and slag waste processing is shown. Besides, profitability of the project is presented.     

Modelling of composting of food waste in a column reactor

The composting of organic solid waste, the mixture of fruit and vegetable leftovers enriched with night soil, was investigated in a closed thermally insulated reactor. It was found that 80.9 % of the original substrate biodegraded after 14 days. A mathematical model of the column reactor was proposed where the biodegradation rate of the organic solid waste was described using simple n-thorder kinetics. A good prediction of process performance was obtained using the proposed kinetics and experimentally obtained reaction heat. Presented at the 33rd International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 22–26 May 2006.     

Correlation between the Mechanical Properties and the Amount of Desorbed Water for Composites Based on Low-Density Polyethylene and Linen Yarn Production Waste

The effect of the amount of desorbed water on the mechanical properties of composites based on low-density polyethylene and linen yarn production waste (LW) is analyzed by statistical methods. It is shown that the amount of absorbed water decreases during the desorption process at room temperature both for specimens modified and unmodified with diphenylmethane diisocyanate (DIC.) The most sensitive to the action of water is the elastic modulus, which decreases considerably under the effect of water and is fully restored in the desorption process. The tensile strain also increases with the amount of absorbed water. It is found that the elastic modulus of the unmodified composite correlates linearly with the amount of desorbed water. Between the amount of desorbed water and the tensile strain, as well the specific work of deformation, a negative linear correlation is revealed. After water desorption, all strength and deformation characteristics of both the modified and unmodified composites are fully recovered.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 515–524, July–August, 2005.     

可压缩核废料污染问题的修正迎风差分格式及收敛性分析

对无弥散项的可压缩核废料污染问题模型建立修正迎风差分格式,并进行了收敛性分 析,最后给出其l2误差估计．     

Innovative stabilization/solidification processes of fly ash from an incinerator plant of urban solid waste

Fly ash samples from an incineration plant of urban solid waste (USW) were submitted to a stabilization/solidification process based on encapsulation with a polyester resin. With this process, a very limited increase of about 25% in weight and a compressive strength as high as 1200 kg/cm² can be obtained. The efficiency of the process to stabilize/solidify the residues and to reduce the pollutant release was evaluated by performing both mechanical and leaching tests following the IRSA–CNR standard method. The leaching test was based on treating the sample with an acetic acid solution adjusted to pH 5.2 for 24 h under magnetic stirring. Toxic metals (Pb, Cd, and Cu) and organic pollutants (PAHs, PCBs, and OCPs) were determined in raw fly ash samples and in the leaching solutions of treated samples. Raw residues showed higher concentrations of trace metals than the regulatory limits, whereas the stabilized/solidified residues showed a concentration of all the pollutants lower than the regulatory limits and a compressive strength much higher than the suggested minimum value. Finally, a critical comparison with conventional stabilization/solidification processes based on the use of Portland cement highlighted that the polyester resin-based process performed much better in terms of the release of both organic and inorganic pollutants, thus substantially lowering the environmental impact of these residues.     

余热驱动的传热强化吸附制冰机实验研究

以活性炭-甲醇为工质对,搭建单床吸附制冰机。采用某种粘结剂与活性炭混合。制作具有良好传热性能的固化活性炭块。吸附床即由此种炭块和带铜肋片的传热管组成。本文针对渔船制冰工况(冷量温度控制在零下7℃)对制冰机进行了模拟试验。系统的性能参数如下:COP为0.07,SCP为11W/kg活性炭。